Whenever an error occur showing "Sorry, a problem has occured", it's usually followed by an error number. This error number or code helps Programmers know where to start troubleshooting on the problem.

Notice: For additional information, refer to Newton Programmer's Reference for Newton version 2.0

General Errors (0, -7000 & positive codes)	State Machine Errors (-8601 to -8608 codes)
Application Errors (-8001 to -8105 codes)	Operating System Errors (-10000 to -10079 codes)
I/O Box Errors (-8301 to -8303 codes)	Stack Errors (-10200 to -10206 codes)
View System Errors (-8501 to -8505 codes)	Package Errors (-10401 to -10410 codes)

PCMCIA Errors (-10501 to -10535 codes)	DMA Errors (-10800 to -10823 codes)
Flash Card Errors (-10551 to -10559 codes)	Heap Errors (-10900 to -10908 codes)
Card Store Errors (-10600 to -10622 codes)

AppleTalk Errors (-12001 to -12016 codes)	Communications Tool Errors (-16001 to -16024 codes)
LAP Protocol Errors (-12100 to -12104 codes)	Serial Tool Errors (-18000 to -18013 codes)
DDP Protocol Errors (-12200 to -12213 codes)	MNP Tool Errors (-20001 to -20011 codes)
NBP Protocol Errors (-12300 to -12314 codes)	FAX Tool Errors (-22001 to -22007 codes)
AEP Protocol Errors (-12400 to -12403 codes)	Modem Tool Errors (-24000 to -24009 codes)
RTMP Protocol Errors (-12500 to -12505 codes)	Communication Manager Errors (-26000 to -26015 codes)
ATP Protocol Errors (-12600 to -12612 codes)	Docker Errors (-28001 to -28107 codes)
PAP Protocol Errors (-12700 to -12716 codes)	Docker Import & Export Errors (-28200 to -28210 codes)
ZIP Protocol Error (-12800 code)	Docker Disk Errors (-28300 to -28304 codes)
ADSP Protocol Errors (-12900 to -12904 codes)	Docker Desktop DIL Errors (-28700 to -28805 codes)
Utility Class Errors (-14001 to -14011 codes)

Sound Errors (-30000 to -30012 codes)	Sharp IR Errors (-38001 to -38008 codes)
Compression Errors (-32001 to -32101 codes)	Online Service Errors (-40102 to -40106 codes)
Memory Errors (-34000 to -34020 codes)	Printing Errors (-44000 to -44108 codes)
Communication Transport Errors (-36001 to -36030 codes)	Newton Connection Errors (-46001 to -46005 codes)

Store & Soup Errors (-48001 to -48033 codes)	Interpreter Errors (-48800 to -48815 codes)
Object System Errors (-48200 to -48222 codes)	Communication EndPoint Errors (-54000 to -54027 codes)
Bad Type Errors (-48400 to -48425 codes)	Tablet Driver Errors (-56001 to -56102 codes)
Compiler Errors (-48600 to -48628 codes)	Battery Driver Errors (-56201 to -56203 codes)

Alien Store Errors (-58001 to -58005 codes)

Error Code	Description
0	No error
-7000	Not enough memory available
77 or higher	Any Positive error code is usually a bus error, restarting the Newton usually fixes the problem.

Error Code	Description
-8001	PCMCIA card battery must be replaced
-8002	PCMCIA card battery is running low
-8003	Nothing to undo
-8004	The routing slip is already open
-8005	Close box must be tapped to hang up the modem
-8006	Nothing to print
-8007	Exception not handled
-8008	The length of a styles slot had to be extended
-8009	A length in the read-only styles slot is too short to display the text
-8010	Communications card has been inserted
-8011	Note has too many items
-8012	Note is too large
-8013	Note is too long
-8100	Blank note could not be created
-8101	Item could not be moved
-8102	Changes could not be saved
-8103	A problem has occurred
-8104	Problem with the PCMCIA card
-8105	Note could not be changed

Error Code	Description
-8301	Missing transport
-8302	Missing slip
-8303	Cannot convert

Error Code	Description
-8501	Could not create view
-8502	Missing class slot
-8503	Unknown view stationery
-8504	Missing view flags
-8505	Missing view bounds

Error Code	Description
-8601	Invalid state
-8602	No state
-8603	No wait state
-8604	No polling routine
-8605	Polling timed out
-8606	Aborted
-8607	No reentrance
-8608	Invalid mode

Error Code	Description
-10000	Bad domain object ID
-10001	Bad physical page object ID
-10002	Unexpected object type
-10003	No page table
-10004	Allocation on an uninitialized heap
-10005	Call not implemented
-10006	Bad parameters
-10007	Not enough memory
-10008	Item not found
-10009	Could not create object
-10010	Must use a remote procedure call
-10011	Bad object
-10012	Not a user call
-10013	Task does not exist
-10014	Unexpected end of message
-10015	Bad object ID
-10016	Bad message object ID
-10017	Message already posted
-10018	Cannot cash token
-10019	Port no longer exists
-10020	No message waiting
-10021	Communications problem (message timed out)
-10022	Bad semaphore group ID
-10023	Bad semaphore operation list ID
-10024	Semaphore group no longer exists
-10025	Semaphore would cause blocking
-10026	Task no longer exists
-10027	Task aborted
-10028	Cannot suspend blocked task
-10029	Bad register number
-10030	Bad monitor function
-10031	No such monitor
-10032	Not a monitor
-10033	Size too large in shared memory call
-10034	Shared memory mode violation
-10035	Object not owned by task
-10036	Object not assigned to task
-10037	Total confusion
-10038	Another task already blocking
-10039	Cancelled
-10013	Task does not exist
-10014	Unexpected end of message
-10015	Bad object ID
-10016	Bad message object ID
-10017	Message already posted
-10018	Cannot cash token
-10019	Port no longer exists
-10020	No message waiting
-10021	Communications problem (message timed out)
-10022	Bad semaphore group ID
-10023	Bad semaphore operation list ID
-10024	Semaphore group no longer exists
-10025	Semaphore would cause blocking
-10026	Task no longer exists
-10027	Task aborted
-10028	Cannot suspend blocked task
-10029	Bad register number
-10030	Bad monitor function
-10031	No such monitor
-10032	Not a monitor
-10033	Size too large in shared memory call
-10034	Shared memory mode violation
-10035	Object not owned by task
-10036	Object not assigned to task
-10037	Total confusion
-10038	Another task already blocking
-10039	Cancelled
-10040	Object already initialized
-10041	Nested collection
-10042	Shared memory message no longer exists
-10043	Receiver did not perform remote procedure call
-10044	Copy aborted
-10045	Bad signature
-10046	Call not in progress
-10047	Token expected
-10048	Receiver object no longer exists
-10049	Monitor is not suspended
-10050	Not a fault monitor
-10051	No available page
-10052	Interrupt not enabled
-10053	Interrupt not implemented
-10054	Tric interrupt not enabled
-10055	Tric interrupt not implemented
-10056	Unresolved fault
-10057	Call already in progress
-10058	Offset beyond data
-10059	Bus access
-10060	Access permission
-10061	Permission violation
-10062	Duplicate object
-10063	Ill formed domain
-10064	Out of domains
-10065	Write protected
-10066	Timer expired
-10067	Not registered
-10068	Already registered
-10069	System restarted due to a power fault
-10070	System restarted because the battery was dead
-10072	System restarted because a PCMCIA card was removed while in us
-10073	RAM table is full
-10074	Unable to satisfy request
-10075	System error
-10076	System failure
-10077	New system software
-10078	Resource is claimed
-10079	Resource is unclaimed

Error Code	Description
-10200	Stack too small
-10201	No room for heap
-10202	Stack is corrupted
-10203	Stack overflow
-10204	Stack underflow
-10205	Address out of range
-10206	Bad domain

Error Code	Description
-10401	Bad package
-10402	Package already exists
-10403	Bad package version
-10404	Unexpected end of package
-10405	Unexpected end of package part
-10406	Part type is already registered
-10407	Part type is not registered
-10408	No such package exists
-10409	Newer package already exists
-10410	Newer version of application already installed

Error Code	Description
-10501	Unrecognized card
-10502	Card not ready
-10503	Bad power on card
-10504	Unexpected card error
-10505	Card reset
-10506	Card is not initialized
-10507	Card service is not installed
-10508	Card service is not suspended
-10509	Card service has not been resumed
-10510	No usable configurations on card
-10511	Card could not be formatted
-10512	Card could not be formatted because it is write-protected
-10520	Bad CIS parser procedure pointer
-10521	Unknown tuple in CIS
-10522	Unknown subtuple in CIS
-10523	CIS tuple order is bad
-10524	CIS tuple size is bad
-10525	CIS tuple specified as no link has a link
-10526	CIS tuple specified with a link has no link
-10527	CIS tuple link target is bad
-10528	Bad CIS tuple version 1
-10529	Bad CIS tuple version 2
-10530	Bad CIS JEDEC tuple
-10531	Bad CIS checksum
-10532	Missing CIS
-10533	Blank CIS
-10534	Bad CIS
-10535	Bad link target

Error Code

Description

-10551	Flash card is busy
-10552	Flash card is not erasing
-10553	Flash card erase is not suspended
-10554	Flash card suspend erase error
-10555	Flash card erase failed
-10556	Flash card write failed
-10557	Flash card Vpp is low
-10558	Flash card error in sleep
-10559	Flash card does not have enough power

Error Code

Description

-10600	Attempt to read or write outside of object bounds
-10601	Bad buffer pointer
-10602	Bad card access
-10603	Bad storage type
-10604	Store not found
-10605	The store has been write-protected by the user
-10606	Object not found
-10607	Flash card block is full
-10608	Flash card is not virgin
-10609	Write error (one or more bits failed to assert)
-10610	No more objects
-10611	Flash card erase in progress
-10612	Card is full
-10613	No more blocks left in search on flash card
-10614	Flash card log is full
-10615	Card needs to be formatted
-10616	Bad or unknown PSSID
-10617	Card memory is full
-10618	Missing or low battery on SRAM card
-10619	Attempt to modify store without a transaction in effect
-10620	Transaction aborted
-10621	Card needs recovery, but it is write-protected
-10622	Object too large for store

Error Code

Description

-10800	DMA mode
-10801	DMA bus access
-10802	DMA buffer doesn't exist
-10803	DMA address word alignment
-10804	DMA count word alignment
-10805	DMA count size
-10806	DMA offset size
-10820	DMA PCMCIA ready
-10821	DMA PCMCIA input acknowledgment
-10822	DMA PCMCIA write protect
-10823	DMA PCMCIA time out

Error Code

Description

-10900	Heap odd block size
-10901	Heap block out of range
-10902	Heap preferred free not found
-10903	Heap free accounting error
-10904	Heap accounting error
-10905	Heap block too big
-10906	Heap bad prior pointer
-10907	Heap bad last pointer in prior
-10908	Heap bad last pointer in last

Error Code

Description

-12001	Buffer too small or corrupted
-12002	Event is pending
-12003	Cancelled
-12004	Attempt to cancel failed
-12005	No handler for cancel
-12006	Unknown message receiver
-12007	Cannot create AppleTalk port
-12008	Cannot create AppleTalk task
-12009	Not implemented
-12010	Data length error
-12011	No such subject available to open
-12012	Not opened
-12013	AppleTalk is not open
-12014	AppleTalk is already open
-12015	Duration is too small
-12016	Duration is too large

Error Code

Description

-12100	LAP read link failed
-12101	LAP all protocols in use
-12102	No protocol handler
-12103	No such command
-12104	Bad link

Error Code

Description

-12200	No such DDP command
-12201	Invalid socket
-12202	Not in static socket range
-12203	Not in dynamic socket range
-12204	Socket is already open
-12205	Socket not open
-12206	Socket internal socket
-12207	Socket is in use
-12208	Unknown LAP type
-12209	DDP back check sum
-12210	Bad packet size
-12211	No listener for socket
-12212	No such protocol type known
-12213	External client timed out

Error Code

Description

-12300	Bad form
-12301	Name is already registered
-12302	Too many names
-12303	Name is not registered
-12304	Too many names requested
-12305	Too many lookups are pending
-12306	Not a NBP packet DDP type
-12307	Unknown NBP function
-12308	Unknown NBP lookup reply
-12309	Too many tuples in lookup request
-12310	NBP lookup is in use
-12311	NBP index out of range
-12312	NBP lookup aborted
-12313	No such command
-12314	No names found

Error Code

Description

-12400	No such command
-12401	Not an echo packet DDP type
-12402	AEP packet size is zero
-12403	AEP function not requested

Error Code

Description

-12500	No such command
-12502	Packet size is zero
-12503	RTMP routed
-12504	RTMP address unresolved
-12505	RTMP no router available

Error Code

Description

-12600	No such command
-12601	No ATP packet DDP type
-12602	Unknown ATP function
-12603	ATP request data length is zero
-12604	Expected responses are out of range
-12605	Response buffer is too small
-12606	ATP retry duration too small
-12607	ATP transaction timed out
-12608	Responding socket already open
-12609	Responding socket not open
-12610	Response packet length bad
-12611	Bad number of response packets
-12612	Socket already has a request on autorequest

Error Code

Description

-12700	No such command
-12701	Unexpected connection ID
-12702	Invalid connection ID
-12703	Invalid responder socket
-12704	Unexpected function
-12705	Printer is busy
-12706	Unexpected connection open result
-12707	Bad flow quantum requested
-12708	Connection timed out
-12709	EOF sent
-12710	PAP flushed
-12711	Printer terminated connection
-12712	Printer not found
-12713	No status available
-12714	No data available
-12715	The buffer that was passed is too small
-12716	Put data operation timed out

Error Code	Description
-12800	No zones

Error Code

Description

-12900	Too many ADSP connections
-12901	ADSP mode invalid
-12902	ADSP packet size bad
-12903	ADSP control type bad
-12904	Remote end disconnected

Error Code

Description

-14001	Not implemented
-14002	Out of memory
-14003	Bad position
-14004	Already initialized
-14005	Invalid size
-14006	Overflow
-14007	Underflow
-14008	Range check failed
-14009	Element sizes do not match
-14010	Not initialized
-14011	Pointer is nil

Error Code

Description

-16001	Command in progress
-16002	Bad command
-16003	Tool already has maximum requests pending
-16004	Buffer overflow
-16005	Request canceled by kill request
-16006	Bad parameter in request
-16007	Connection end has not been created yet
-16008	Invalid call when connected
-16009	Phone connection was cut off, or invalid call when not connected
-16010	Connection negotiation failed because remote end is not compatible with local end configuration
-16011	Connection terminated or failed due to retransmission limit of data or connect packet
-16012	No data available for TCommToolGetRequest when fNonBlocking is true.
-16013	Connection aborted by disconnect
-16014	Call not supported
-16015	Request not pending
-16016	Event not pending
-16017	Time-out waiting for connection
-16018	Connection end is already bound
-16019	Connection end was not bound before use
-16020	Connection end is being released
-16021	No phone number was provided
-16022	Operation failed because a resource was not available
-16023	Call failed because the option passed is not supported
-16024	The method is not implemented

Error Code

Description

-18000	Serial channel is in use
-18001	Memory error
-18002	Not current owner of the serial port
-18003	Framing or parity overrun, or bad connection
-18004	CRC error on input framing
-18005	An internal error has occurred
-18006	Packet size too large or too small in an output request
-18007	Unexpected packet length
-18008	EOF not found
-18009	Overrun bit was set
-18010	Too many collisions when sending packet
-18011	Too many deferrals when sending packet
-18012	Timed out waiting for an event
-18013	Serial tool is not active or ready

Error Code

Description

-20001	Connection parameter negotiation failed
-20002	Acceptor of connect request timed out
-20003	Not connected
-20004	Request aborted by disconnect request
-20005	Link attention service is not enabled
-20006	Request retry limit of connect initiator reached
-20007	Command already in progress
-20008	Connection already established
-20009	Connection failed due to incompatible protocol levels
-20010	Connection handshake failed
-20011	Memory for MNP not allocated

Error Code

Description

-22001	Lost connection while sending or receiving FAX
-22002	FAX machine is not compatible
-22003	Transmission error
-22005	FAX machine had a problem sending some pages
-22006	Transmission error
-22007	Transmission error

Error Code

Description

-24000	No modem is connected
-24001	There is no dial tone
-24002	There is no answer
-24003	The phone number is busy
-24004	There is no answer
-24005	The modem is not responding properly
-24006	FAX carrier error
-24007	The modem is not responding properly
-24008	The modem connected to the serial port does not support cellular connection
-24009	The AT+FRH command timed out when receiving flags

Error Code

Description

-26000	Service already initialized
-26001	Unknown command
-26002	Unknown service
-26003	Service already exists
-26004	No service specified in the options array
-26005	There is no registered service matching the type specified in the options array
-26006	No endpoint exists; this is usually because CMStartService has not been called
-26007	No public port exists; this is usually because CMGetEndPoint has not been called
-26008	No known last connected device
-26009	A tuple has been received, but no the device ID tuple
-26010	A service information response tuple was expected
-26011	Unsupported service; can only load packages
-26012	An SCP load is in progress and another cannot be issued
-26013	The SCP load call is not supported on this machine
-26014	Cannot process this speed
-26015	The SCP loader did not previously load a package

Error Code

Description

-28001	Invalid store signature
-28002	Invalid entry
-28003	Aborted
-28004	Invalid query
-28005	Read entry error
-28006	Invalid current soup
-28007	Invalid command length
-28008	Entry not found
-28009	Bad connection
-28010	File not found
-28011	Incompatible protocol
-28012	Protocol error
-28013	Docking canceled
-28014	Store not found
-28015	Soup not found
-28016	Invalid header
-28017	Out of memory
-28018	Newton version too new
-28019	Package cannot load
-28020	Protocol already registered
-28021	Remote import error
-28022	Bad password error
-28023	Password retry
-28024	Idle too long
-28025	Out of power
-28026	Invalid cursor
-28027	Already busy
-28028	Desktop error
-28029	Cannot connect to modem
-28030	Disconnected
-28031	Access denied
-28100	Disconnect during read
-28101	Read failed
-28102	Communications tool not found
-28103	Invalid modem tool version
-28104	Card not installed
-28105	Browser File Not Found
-28106	Browser Volume Not Found
-28107	Browser Path Not Found

Error Code

Description

-28200	Syntax error
-28201	Invalid version
-28202	Could not open temporary store
-28203	Could not convert
-28204	Invalid criteria
-28205	Error applying script
-28206	Missing meta data
-28207	Unknown error
-28208	Scanner overflow error
-28209	Data Viz translator error
-28210	Invalid type

Error Code

Description

-28300	Disk full
-28301	File not found
-28302	File is write protected
-28303	Duplicate file name
-28304	Too many files open

Error Code

Description

-28700	No Error
-28701	Out of memory
-28702	Invalid pipe state
-28703	Exception error
-28704	Queue full
-28705	Pipe not initialized
-28706	Invalid parameter
-28707	Pipe not ready
-28800	No Error
-28801	Out of object heap memory
-28802	Out of temporary memory
-28803	Unknown slot
-28804	Slot size exceeded
-28805	Slot size required

Error Code

Description

-30000	Generic sound error
-30001	Not enough memory available
-30002	Invalid message
-30003	Sound was not played
-30004	No channel decompressor
-30005	Destination buffer too small
-30006	Sound player busy
-30007	Sound recorder busy
-30008	No samples provided
-30009	Unsupported sound configuration
-30010	Sound channel closed
-30011	Sound cancelled
-30012	The sound volume is set to zero

Error Code

Description

-32001	Cannot compress in place
-32002	Parsing error
-32003	Invalid type
-32004	Compression not achieved
-32005	Key not found
-32006	Compression index error
-32007	Cannot decompress in place
-32008	Decompression not achieved
-32009	Unexpected end of source
-32100	Buffer overflow
-32101	Buffer underflow

Error Code

Description

-34000	Not free, direct or indirect
-34001	Pointer not aligned to 4-byte boundary
-34002	Pointer to outside of heap
-34003	Unknown infrastructure type
-34004	Free block where there shouldn't be one
-34005	Free list pointer points outside of heap
-34006	Free-list pointer doesn't point at a free block
-34007	Invalid block size
-34008	Forbidden bits set in block size
-34009	Less than minimum size for heap block
-34010	Heap block tool large
-34011	Total free space is more than space for entire heap
-34012	Nil pointer where not allowed
-34013	Actual free space does not match tracked free space
-34014	Linked free space does not match tracked free space
-34015	Master pointer doesn't point back to a handle block
-34016	Invalid block size adjustment
-34017	Internal block may be mangled
-34018	The heap is invalid
-34019	Caught an exception while checking the heap
-34020	Invalid heap header

Error Code

Description

-36001	Incorrect address format
-36002	Incorrect option format
-36003	Incorrect permissions
-36005	Could not allocated address
-36006	Operation not supported in the current tool state
-36008	System error
-36012	Flow control problem
-36018	Unsupported primitive
-36019	State change is in process
-36030	There's already a synchronous call pending

Error Code

Description

-38001	No response - protocol time out
-38002	Cancelled - remote side cancelled operation
-38003	Protocol error
-38004	Data checksum failed
-38005	Remote side receive failed
-38006	Bad connection - allowed number of retries exceeded
-38007	SCC data errors on receive
-38008	Unspecified beaming error

Error Code

Description

-40102	Lost connection to host
-40103	Lost connection to host
-40104	The host is not responding
-40105	There is a problem reading from the host
-40106	Failed to connect to local access number

Error Code

Description

-44000	Printer problem
-44001	Newton is unable to print
-44002	No printer is connected
-44003	Printer busy
-44004	Printing stopped
-44005	Lost contact with the printer
-44006	Image too complex for printer
-44100	The next sheet of paper must be inserted
-44101	The phone number must be dialed now
-44102	There is no paper tray
-44103	The wrong paper tray is attached
-44104	The printer has no paper
-44105	The printer has no ink
-44106	The printer is jammed
-44107	The printer door is open
-44108	The printer is off-line

Error Code

Description

-46001	Connection initialization failed
-46002	Timer error
-46003	Connection request was denied by the remote
-46004	Unable to connect because there are no endpoints available
-46005	A connect request was received but no service name was given

Error Code

Description

-48001	The PCMCIA card is not a data storage card
-48002	Store format is too old to understand
-48003	Store format is too new to understand
-48004	Store is corrupted, can't recover
-48005	Single object is corrupted, can't recover
-48006	Object stream has unknown format version
-48007	Fault block is invalid
-48008	Not a fault block
-48009	Not a soup entry
-48010	Tried to remove a store that was not registered
-48011	Soup index has an unknown type
-48012	Soup index has an unknown key structure
-48013	Soup index does not exist
-48014	A soup with this name already exists
-48015	Tried to CopyEntries to a union soup
-48016	Soup is invalid (probably from a removed store)
-48017	Soup is invalid (probably from a removed store)
-48018	Entry is invalid (probably from a removed store)
-48019	Key does not have the type specified in the index
-48020	Store is in ROM
-48021	Soup already has an index with this path
-48022	Internal error-something unexpected happened
-48023	Tried to call RemoveIndex on the _uniqueID index
-48024	Query type missing or unknown
-48025	Discovered index inconsistency
-48026	Maximum number of soup tags reached
-48027	Soup does not have a tags index
-48028	Invalid tags specification in the query
-48029	Store cannot handle the feature (for example, large objects)
-48030	Unknown sorting table
-48031	Cannot do union soup because of different sorting tables
-48032	Invalid index description
-48033	Cannot use virtual objects for soup entry keys

Error Code

Description

-48200	Expected a frame, array, or binary object
-48201	Invalid magic pointer
-48202	Empty path
-48203	Invalid segment in path expression
-48204	Path failed
-48205	Index out of bounds (string or array)
-48206	Source and destination must be different objects
-48207	Long out of range
-48210	Bad arguments
-48211	String too big
-48212	Expected a frame, array, or binary object
-48213	Expected a frame, array, or binary object
-48214	Object is read-only
-48216	Out of heap memory
-48217	Invalid attempted use of magic pointer
-48218	Cannot create or change an object to negative size
-48219	Value out of range
-48220	Could not resize locked object
-48221	Reference to deactivated package
-48222	Exception is not a subexception of |evt.ex|

Error Code

Description

-48400	Expected a frame
-48401	Expected an array
-48402	Expected a string
-48403	Expected a frame, array, or binary object
-48404	Expected a number
-48405	Expected a real
-48406	Expected an integer
-48407	Expected a character
-48408	Expected a binary object
-48409	Expected a path expression (or a symbol or integer)
-48410	Expected a symbol
-48411	Expected a function
-48412	Expected a frame or an array
-48413	Expected an array or nil
-48414	Expected a string or nil
-48415	Expected a binary object or nil
-48416	Unexpected frame
-48417	Unexpected binary object
-48418	Unexpected immediate
-48419	Expected an array or string
-48420	Expected a virtual binary object
-48421	Expected a package
-48422	Expected nil
-48423	Expected nil or a symbol
-48424	Expected nil or true
-48425	Expected an integer or an array

Error Code

Description

-48600	Could not open a listener window
-48601	Syntax error
-48603	Cannot assign to a constant
-48604	Cannot test for subscript existence; use length
-48605	Global variables not allowed in applications
-48606	Cannot have a global variable and a global constant with the same name
-48607	Cannot redefine a constant
-48608	Cannot have a variable and a constant with the same name in the same scope
-48609	Non-literal expression for constant initializer
-48610	End of input inside a string
-48611	Odd number of digits between \\u's
-48612	No escapes but \\u are allowed after \\u
-48613	Invalid hex character in \\u string
-48617	Two-digit hex number required after $\\ escape
-48618	Four-digit hex number required after $\\u
-48619	Illegal character '%c'
-48620	Invalid hexadecimal integer: %s (out of range)
-48621	Invalid real number (out of range)
-48622	Invalid decimal integer: %s (out of range)
-48626	#xxxx not allowed from NTK
-48627	Not a constant
-48628	Decimal digit required after @

Error Code

Description

-48800	Not in a break loop
-48803	Wrong number of arguments
-48804	FOR loop BY expression has value zero
-48806	No current exception
-48807	Undefined variable
-48808	Undefined global function
-48809	Undefined method
-48810	No _proto for inherited send
-48811	Tried to access slot of nil
-48814	Local variables and FOR/WITH loops not allowed at top level
-48815	The operation would make the rich string invalid

Error Code

Description

-54000	No active input script
-54001	Badly formed script
-54002	Zero length data
-54003	Expected a specification
-54004	Invalid option
-54005	Invalid end sequence
-54006	Inappropriate partial
-54007	Inappropriate termination
-54008	Inappropriate target
-54009	Inappropriate filter
-54010	Expected target
-54011	Expected template
-54012	Input specification already active
-54013	Invalid proxy
-54014	No endpoint available
-54015	Inappropriate call
-54016	Character is not single byte
-54021	Option failure
-54022	Option partial success
-54023	Option read only
-54024	Option not supported
-54025	Invalid option op code
-54026	Option not found
-54027	Option truncated

Error Code

Description

-56001	Attempted to call the tablet driver before it was loaded
-56002	Attempted to create a tablet driver a second time
-56003	Creation of tablet driver failed
-56004	Unable to enter bypass mode
-56005	Not in bypass mode
-56006	Cannot add sample to buffer
-56007	No new data since last polling time
-56008	Unsupported function
-56101	Timeout when calibrating
-56102	Calibration aborted

Error Code	Description
-56201	Could not find battery driver
-56202	Battery error
-56203	Invalid battery selector

Error Code	Description
-58001	Oversize page
-58002	No such page
-58003	Cannot repage ID
-58004	No more for that page
-58005	Store is damaged